There are very few irritations than a slightly damaged flush. Especially, when you cannot help being neat all the time. It’s not only irritating but unacceptable. The problem feels more overwhelming when you do not know the probable reasons why it can happen. Therefore, we are here to help you with five possible reasons why your toilet bowl water is low. So, you can explain to your plumber in Reading why your flush stopped working. Most importantly, it is of utmost importance to know where the root cause of a problem lies. Let us dive deeper!
Before you call a plumber to fix your poorly working flush, ensure that the water supply in your bathroom is fine. Also, check if something has accidentally triggered the shut-off valve on your toilet, as this would mean that your toilet has no access to water.
If the water supply is running accordingly and the shut-off valve is off, then you’ll want to proceed to the following solutions.
There’s A Problem with the Toilet Tank
One of the easiest problems to fix is a lack of water in your toilet tank. This is the root cause behind numerous toilet repair problems. Most of the time, it involves the toilet fill valve or flapper. The fill valve, also known as the ballcock, controls how much water fills the tank. If the mechanisms are misaligned or broken, the toilet tank won’t fill to the correct amount. The tank water level can be too low to fill up the bowl when this happens.
Similarly, you might experience low water levels in the basin, if there is a problem with the flapper that drains the water from your toilet tank to the bowl. Try and adjust the water level in the toilet bowl to get it back to normal.
How to Fix the Toilet Tank Mechanism
You can apply two ways to fix a toilet with a toilet tank that isn’t working properly:
- Adjust the toilet valve
- Replace the broken parts
You need to remove the cover of your toilet tank to figure out which option you need.
Inspect the fill valve and flapper to see if there is a worn or broken component. Any expert Plumber in Reading will adjust the fill valve if it’s not damaged. Depending on the type of toilet you have, the fill valve mechanics may work differently. So, check the manufacturer’s manual when inspecting your toilet.
Apply a DIY flapper fix to repair the toilet if you notice a broken valve or flapper. Oftentimes, a quick trip to the hardware store and the right replacement parts will do the job!
A Partial or Full Clog Is Detected
A clog is an old and gold reason behind low toilet bowl water. The most common type of clog is one in the internal piping of your toilet which often causes a toilet to overflow. Sometimes, the blockage siphons water out of the toilet bowl, causing low water levels.
If a partial clog is causing your toilet’s low water levels, one of the best ways to detect is by observing how the toilet flushes. Therefore, Plumbers in Readingsuggest that you check the water level of your toilet. If the water levels rise to the top of your toilet only to slowly go down until water levels are below normal, chances are this siphoning issue is somewhere in the trap of your toilet.
How to Fix a Partial or Full Clog
Just by removing the blockage, this issue can be fixed. Use a gloved hand, toilet plunger, or toilet auger to remove the obstruction. If you suspect that there is a blockage deep within the pipes, you may need to contact a professional Plumber in Reading.
Clogged Inlet Holes Can Be the Reason
Clogged inlet holes often cause low water in a toilet. Also, known as rim jets, these holes can be found just under the rim of your toilet. Depending on the type of toilet and the quality of your tap water, the water draining from the tank into the bowl can calcify and get plugged in.
How to Fix Clogged Inlet Holes
Adding hot vinegar to the clogged inlet hole is the easiest way to get rid of it. You will want to let the vinegar soak for a good couple of hours to help dissolve calcium deposits.
So, it’s advisable that use a toothbrush to scrub away the deposits or, if they’re compacted, poke a small wire inside the holes to clear them out. Then, flush the toilet to see if this trick did the job.
These are some possible reasons for a low-water toilet. Sometimes, your toilet can face other issues as well. If you are unable to recognize that, call a plumber in Reading. They will address the root cause and resolve the issue in an eye’s blink.